|
Step Global |
|---|
GNSS (Global Navigation Satellite System) signal distribution involves amplifying, repeating, and distributing signals to various receivers, devices or across different locations. This distribution allows multiple devices to access GNSS signals from a single antenna, because of this it is often more cost-effective to distribute the signal as opposed to installing individual antennas for each device. Signal distribution is often used in applications where location or timing data is required but GNSS signals are limited or obstructed. This signal obstruction can occur in urban environments such as cities where large buildings make accessing satellite signals challenging.
Step Global provides solutions for all your GNSS signal distribution requirements, we provide GNSS signal splitters with outputs ranging from 2-32, we also supply signal amplifiers, attenuators, combiners, filters, and repeaters. We also provide a range of products for UHF and RFID signal distribution.
Product Code: S18-A
Brand: GPS Source
A GPS splitter allows a single GPS antenna to be shared between multiple GPS receivers. The S18-A GPS, Galileo, GLONASS Splitter is a one input eight output RF device. The most common application is where the input from an active GPS roof antenna or GPS simulator is split to eight receiving GPS units. The S18 is available with more customizable options than any competitive product on the market.
Product Code: S18GT
Brand: GPS Source
The S18GT will support long-lasting, trouble free deployment in a small cell wireless and/or DAS environment. The device makes it possible to use a single GPS referencing antenna for synchronization systems, increasing capacity without increasing GPS antennas or cabling requirements. Power is obtained from the GPS receiver(s) connected to the amplifier. There is no need for a...
Product Code: IRMS18
Brand: GPS Source
The IRMS18 single input, 8 output splitter amplifies and the GPS/GNSS signal from one GPS receive antenna while granting up to 8 GPS/GNSS receivers signal access at any time. The most common use being the input from an active GPS roof antenna or GPS simulator is split to eight receiving GPS units or timing boards. A GNSS receiver within the IRMS132 monitors the antenna signal strength. There is...
Product Code: S18WI
Brand: GPS Source
The S18WI is designed to be ruggedized. The cost of multiple antennas and long cable runs is eliminated. The S18WI can be configured to monitor the GPS antenna current, providing an alarm indication if the antenna is not operating according to specifications. The S18WI features an optional DC bias Pick & Choose circuit which allows for the active antenna DC input to be applied to any or all...
Product Code: MS18
Brand: GPS Source
This is a military qualified MS18 GPS splitter with one-input and eight-outputs. It typically finds application where an input from an active GPS roof antenna is split evenly between eight receiving GPS units. The MS18 can be configured to pass DC from an RF output (J2) to the antenna input port (J1) in order to power an active GPS antenna on that port. The remaining RF outputs (J3 thru J9)...
Product Code: RMS18
Brand: GPS Source
The RMS116 GPS/Galileo/GLONASS Splitter is a 1-input 16-output rack mount RF device. The most common use being the input from an active GPS roof antenna or GPS simulator is split to sixteen receiving GPS units or timing boards.
Product Code: S18S -A
Brand: GPS Source
The S18S GPS, Galileo, GLONASS Splitter is a one input eight output RF device. The most common application is where the input from an active GPS roof antenna or GPS simulator is split to eight receiving GPS units. The S18 is available with more customizable options than any competitive product on the market.
Product Code: G-SP8/AN-DCI-7
Brand: Global Invacom
The Global Professional GPS ACTIVE 8 way Splitter has been designed to allow the signal from a GPS antenna to be shared between two receivers. The unit is configured to insert 5V DC to the antenna port via a DC regulator. Both output ports incorporate a 200 Ohm DC load to simulate an antenna DC Current draw. DC is blocked to both output ports.
Product Code: L-SP8/AN-DC1
Brand: Global Invacom
The Global Professional L BAND ACTIVE 8 way Splitter has been designed to split the L band from a typical satellite system with negligible insertion loss. Port one will allow DC to pass through from receiver through to the combined input port. All other ports are DC blocked.The unit can be powered via port one or alternatively external powering is available. PSU’s are available if...
Product Code: L-SPCO8/PN-DC1
Brand: Global Invacom
The Global Professional L BAND PASSIVE 8 way Combiner/Splitter has been designed to combine or split the L band from a typical satellite system. The unit can be used in either configuration as splitter or combiner. Port one will allow DC to pass through from receiver port one through to the combined output port. All other ports are DC blocked. L-Band Splitters can also be supplied as rack mount...
Product Code: U-SP8 A
Brand: Global Invacom
The Global Professional UHF / IF BAND ACTIVE 8 way Splitter has been designed to split a UHF or IF signal with low insertion loss.Dependant on configuration the unit can be powered either by Port 1 or external PSU available separately. The picture illustrates a N type splitter with DC passing on port 1 and remaining port blocked however other configura- tions are available. Configurable...
Product Code: U-SP8 P
Brand: Global Invacom
The Global Professional UHF / IF BAND PASSIVE 8 way Combiner/Splitter has been designed to combine or split a UHF or IF signal. The unit can be used in either configuration as splitter or combiner. The picture illustrates a N type splitter with DC passing on port 1 and Port 2 blocked however other configurations are available . Configurable connector type and DC blocking ports.
