Step Global Home
LabSat 3 Triple Constellation Replay and Record System

Race Logic

LabSat 3 Triple Constellation Replay and Record System


$ List Price (ex GST)

On Backorder

Minimum Order: 1

 Product Code: RLLS03-3RP

Category: LabSat Simulators

Brand: Race Logic

Weight: 2.000000 KG

Click Image to Enlarge

LS03-3-V2 LabSat 03 3-Channel Unit with Internal Batt Pack
RLVBACS020 Mains Power Supply (UK) - Lemo 2W Plug
LS03SDCARD LabSat 3 32GB SDHC Extreme Card
LS03HDD-1TB LabSat 3 Scenario Hard Disk Drive 1TB
RLCAB071-1 SMA Connector - 1SMA Plug-SMA Plug RG174 - 1m Cable
RLCAB082-1 SMA Plug - MCX Plug RG174 - 1m Cable
RLCAB083-1 SMA Plug - MMCX Plug RG174 - 1m Cable
RLCAB084-1 SMA Plug -TNC Plug RG174 - 1m Cable
RLACS202 LabSat 3 Expansion Connector Adapter (includes screwdriver)
RLACS204 USB 3.0 Dual Slot Reader
RLACS197 LabSat 3 Carry Case
RLCAB010L Lemo 2W Plug - Cigar Plug - 2m Cable (Power)
RLACS198 4 Constellation Magnetic Antenna with SMA connector - 4m for use with LabSat 3


  • RLLS03-2RP LabSat 3 Dual Constellation Replay and Record System
  • RLLSSGSW03-2 SatGen V3 Dual Constellation 64Bit Software



SatGen software allows you to create a GNSS RF I&Q or IF data file that can be replayed on a LabSat which is based on a user-generated trajectory file. This allows you to simulate almost any kind of test, at a set time and date, anywhere in the world.

For example, say you are based in the UK, but you have customers for your products in Australia. You can create a test scenario based around Melbourne and check that your equipment works under these conditions.

SatGen complements the LabSat range of GNSS simulators, and is available in single, dual, triple and multi-frequency/multi-constellation versions. The latest version of SatGen can be used to create a single scenario containing all the upper and lower L Band signals for GPS, GLONASS, and BeiDou, and will take advantage of the LabSat 3 Wideband’s ability to read RF data at up to 80 MB/s.

What constellations & signals can I create?

  • Single Constellation - Create single constellation scenario files for GPS L1, GLONASS L1 or BeiDou B1
  • Dual Constellation - Create dual or single constellation scenario files for GPS L1, GLONASS L1 or BeiDou B1
  • Triple Constellation - Create triple, dual or single constellation scenario files for GPS L1, GLONASS L1 or BeiDou B1
  • Wideband - Create LabSat 3 Wideband scenario files for: 
    GPS L1 C/A, M, P; L2, C, P, M; L5, I, Q ( L1M, L2M noise created only)
    BeiDou: B1I, B1-2I, B2I (BeiDou B1 special almanac including BeiDou future satellites)
  • Real-Time – Create real-time GPS, GLONNASS, BeiDou L1 signals with the additional LabSat RT dual constellation system

How does SatGen work?

SatGen can be used to create a scenario which replicates very high dynamic conditions, allowing engineers to test their systems work in all environments. You could simulate an aircraft taking off and going into a vertical climb up to 30,000 feet, and then performing a high g-turn at this altitude, all without leaving your bench!

Creating your own scenarios couldn't be easier. If you have an NMEA file which contains GGA data, then you can import this directly into the software or alternatively, you can start from scratch by creating a route in Google Earth, or build a profile using simple user commands.

Developed with the user in mind, this software allows you to create a static scenario, where a position can be manually inserted or easily determined using the integrated Google Maps screen. You can also draw a route by simply clicking-on a series of locations on the map.

SatGen includes a range of predefined command buttons and scenario examples (including figure-of-eight, circle around a point and aircraft take-off). These pre-set scenarios allow you to test a device by making a few simple clicks.


To find out more about how SatGen can be used to simulate GNSS scenarios, contact or call the Step Global office on +61 3 9551 7334

Is SatGen right for you? Why not try it out?

To enable you to experience the full power of the SatGen Simulation Software, we provide a demonstration version which will allow you to try all new features.

It's a full copy of the SatGen software but is restricted to create GPS-only scenarios (no other constellations) for only 120 seconds. This will allow you to trial the use of SatGen in your own test facility or laboratory.

Please note that the SatGen v3 Simulation Software requires a 64 bit windows operation system and will not install on a 32 bit system.

To receive a free copy of this demo version, please contact or call the Step Global office on +61 3 9551 7334